Skip to content Skip to footer

APT - Architectural Products and Technologies

APT - Architectural Products and Technologies
Close
Lapitec

Fucine di Buttrio

Fucine di Buttrio 01
Fucine di Buttrio 03
Fucine di Buttrio 04
Description:

Marcello d’Olivo’s unique design from 1962 featured an exceptional arched cantilever roof with an impressive 11-meter overhang, supported by ten columns. This architectural masterpiece became a renowned local landmark over the years but unfortunately fell into a state of neglect more recently. However, thanks to the recent efforts of Marco Zito, the building has undergone a comprehensive redevelopment. The objective was to preserve the distinctive elements of the original design while enhancing its efficiency. This redevelopment is an integral part of a larger masterplan known as ‘Le Fucine’, which encompasses a hotel, sports club, winery, and wellness area.

Colour(s) used:
colour sample

Nero Antracite

Application-icon
Applications:

Kitchen

Design-icon
Designed By:

Marcello d’Olivo

FENIX innovative materials

All FENIX innovative materials for interior design are independently certified as Carbon Neutral.

APT is committed to planting – and protecting – one native tree in New Zealand for every FENIX sheet, panel and sink sold. In addition, a native tree will be planted for every product delivery.

Read more about APT’s environmental initiatives here >

Fenix NTM Bloom Colours

SHEET OPTIONS

0.7mm FENIX NTM Bloom sheets are available in two sizes: 3050x1300mm and 4200x1300mm.
Please note: FENIX NTM is directional. Grain direction is indicated by the arrows on the protective film. 

PRESSED PANELS MADE WITH FENIX NTM BLOOM

All New Zealand stocked FENIX ranges and colours can be supplied as a ‘pressed panel’ for vertical and horizontal applications.

Read more about Pressed Panels made with FENIX >

EDGING OPTIONS

Colour matched ABS edging is available in Laser or Standard PU ABS. All edging is available in 23mm and 43mm widths x 1mm thickness.

All FENIX innovative materials for interior design are independently certified as Carbon Neutral.

APT is committed to planting – and protecting – one native tree in New Zealand for every FENIX sheet, panel and sink sold. In addition, a native tree will be planted for every product delivery.

Read more about APT’s environmental initiatives here >

PRESSED PANELS made with FENIX

MDF

FENIX can be pressed on either 18mm MDF (Moisture-Resistant E0), 25mm or 30mm MDF (E0) resulting in an almost 20mm, 27mm or 32mm finished panel thickness. The sheet size is 3.045m x 1.220m.

BIRCH PLYWOOD

FENIX can be pressed on either 18mm or 24mm birch plywood resulting in an almost 20mm or 26mm finished panel thickness. The sheet size is 2.435m x 1.215m.

FENIX Pressed Panels are available in two options*:

  • Face Two Sides (F2S) is where FENIX is pressed onto both faces (or sides) of the substrate for a more premium option.
  • One Face One Back (1F1B) is where FENIX is pressed onto one face (or side) of the substrate, with a similarly coloured ARPA HPL (high-pressure laminate) pressed onto the back face, providing a lower cost option. (FENIX NTM Bloom is currently available in F2S only)

PANEL EDGING OPTIONS

  • Colour-matched Laser ABS edging*, and Standard ABS PU edging are available for the FENIX NTM and FENIX NTM Bloom ranges. The FENIX NTA range is only available in a Standard PU ABS edging only (not laser).
  • Laser ABS edging is available* in colour-matched 23mm and 43mm widths x 1mm thickness
  • Standard ABS PU edging unglued available in colour-matched 23mm and 43mm widths x 1mm thickness
  • FENIX Colour Core edging* in 1.2mm thickness

DARK COLOUR DESIGN CONSIDERATION

Putting dark colour benchtops and cabinetry panels into direct sunlight applications can affect the substrate performance in terms of product movement.